In this NFS configuration guide example, we have explicitly defined additional options -o argument to choose NFSv4 as the preferred option to mount the NFS share.I have divides this tutorial into the NFS server and client sections. Configure NFS ServerLinux file and directory permissions. Mounting and unmounting filesystems.Replace the first section with the IP address of your NFS server and its share path, replace /mnt/nfs with the local virtual mount path you created in the previous step sudo mount 192.168.1.36:/mnt/nfsserver /mnt/nfsTo make the NFS share automount on boot open up your fstab file sudo nano /etc/fstabAdd this line but adjust your IP and mount points (/mnt/nfs), rw stands for read/write so if you only have read access change rw to ro 192.168.1. Install the packages required using the command.Install NFS server components sudo apt-get install nfs-common nfs-server -yCreate the nfs server shared folder, you can use an existing folder as well sudo mkdir /mnt/nfsserverIf you only plan on using the share locally and don't want to mess with permissions, give the mount point you just created liberal permissions. /mnt/nfsserver represents the folder on your NFS server you want to share. Sudo chmod -R 777 /mnt/nfsserverOpen the NFS exports file where you configure the paths to share and their permissions sudo nano /etc/exportsThis is the syntax for the NFS shares and permissions./mnt/nfsserver represents the path to share on the Raspberry PiIP represents the IP address or range and (access) restricts certain types of access like read and write (rw) or read only (ro) /mnt/nfsserver IP(access)Using a wildcard you can grant access to all IP addresses which is of course insecure.It is important not to put a space between the * and the (rw,sync) as it changes the permissions /mnt/nfsserver *(rw,sync)You can also specify a machine or node on the network by its IP /mnt/nfsserver 192.168.1.34 *(rw,sync)You can choose to restrict access to a whole IP range like your entire home network. The /24 represents the subnet mask of your network. Setup Shared Directory with NFS Client for Linux.
Setup Linux Nfs Share Client License File IsAfter an NFS share is created, the applicable shared file system is accessible to clients that run the OS such as SUSE, Red Hat, HP-UNIX, Sun Solaris, IBM AIX, and Mac OS.An NFS share client enables client users to access shared file systems using a network.This section describes how a client accesses an NFS shared file system. (Optional) Configuring the NFSv4 Service to Enable It to BeThis section describes how to configure the NFSv4 service to enable it to be used in a non-domain environment.This section describes how to create an NFS share. (Optional) Configuring a Storage System to AddThis section describes how to add the storage system to an LDAP domain.This section describes how to add the storage system to an NIS domain. The storage system supports NFSv3 and NFSv4. Before configuring a value-added feature, ensure that its license file is valid for the feature.This section describes how to use DeviceManager to configure IP addresses for a storage system.Before configuring an NFS share, enable the NFS service for clients to access the NFS share. The following items need to be planned: networks, domains, permissions, and clients.This section describes the NFS share configuration process.Before configuring an NFS share in a storage system, plan and collect required data to assist in the follow-up service configuration.Each value-added feature requires a license file for activation.Only the interface modules with the same port rate (GE or 10GE) On the same controller, a bond port is formed by a maximum of The port bond mode of a storage system has the following restrictions: Operations used by a client to access an NFS share in an LDAP domain and NIS domain are the same as those used in a non-domain environment.Each port only allows to be added to one bonded port. Read-only users are unable to bind Ethernet ports. SmartIO cards cannot be bonded if they work in cluster or FC modeThe SmartIO port must be the same as that of the host. If Failback Mode is Automatic, ensure that the link to the primary port is normal before the failback.Services will auto fail back to the primary port only when the linkTo the primary port keeps normal for over five minutes.Whether the logical port is activated immediately. If Failback Mode is Manual, ensure that the link to the primary port is normal before the failback.Services will manually fail back to the primary port only when theLink to the primary port keeps normal for over five minutes. Table 3-15 describes related parameters. Enter bond port information. IfA non-Huawei switch is used, contact technical support of the switchManufacturer for specific link aggregation configurations. The link aggregation modes vary with switch manufacturers. Configure the route information for the logical port. Select the locical port for which you want to add aThe Route Management dialog box is displayed. When configuring NFS share access, if the NFS server and logicalIP addresses cannot ping each other, add a route from the logicalIP addresses to the network segment route of the NFS server. IfThey cannot ping each other, add a route from the logical IP addressesTo the network segment of the domain controller server. When a domain controller server exists, ensure that the logicalIP addresses and domain controller server can ping each other. Set Destination Mask (IPv4) or Prefix (IPv6). If IP Address is an IPv6 address, set Destination Address to the IPv6 address or network segment If IP Address is an IPv4 address, set Destination Address to the IPv4 address or network segmentOf the application server's service network port or that of the other Bext file name editor for music macIt is a standardMechanism that represents directories in the text format, and it allowsUsers to import data to and export data from the directory server.LDIF files store LDAP configurations and directory contents, and youCan obtain parameter information from LDIF files. Confirm the information of the dialog box and select I have read and understood the consequences associated with performingThe Success dialog box is displayed indicatingOf the most common file formats for LDAP applications. In Gateway, enter the gateway of the localStorage system's logical port IP address. If a Prefix is set for an IPv6 address, thisParameter specifies the prefix of the IPv6 address for applicationServer's service network port or that of the other storage system's Complicated password is recommended,For example, password contains uppercases, lowercases, digits andConfirm password used by the system to log in to the LDAPUser DN configured by the LDAP domain server.User group DN configured by the LDAP domain server.The timeout duration of client waiting for the search resultFrom server. The group contains user1 and user2.Password may cause security risk. #root on the top#The first user represents user1 that belongs to organization unit user in the organizational structure topology.UserPassword: eoWxtWNl8YbqsulnwFwKMw90Cx5BSU9DRA=xxxxxx#The first user group represents group1 that belongs to organization unit group in the organizational structure topology. ![]() The new nodeMay need to access all other nodes, so all the systems need to modify their /etc/passwd files.
0 Comments
Leave a Reply. |
Details
AuthorMichael ArchivesCategories |